Best Bearings For Lawn Mower Wheels: Compare 10 Options

#1 · Best Overall

1. DEEG 3/4-Inch Bearings

• Material: Alloy Steel
• Material Type: Alloy Steel
• Compatible Lubricant: Grease

Best for: Premium-steel three-quarter-inch fit.

Why it ranks #1: Four GCr15 chrome-steel bearings fit a 3/4-inch axle and 1-3/8-inch hub; double rubber seals and a stated two-year warranty add useful specifics.

DEEG specifies GCr15 chrome steel and 2RS double rubber seals for its four 3/4-inch-bore bearings, pairing a wear-resistant material with protection against outdoor debris. The 1-3/8-inch outside diameter targets a common listed mower-wheel hub size.

The 3/4-inch inner diameter, 1-3/8-inch outer diameter, and 1-1/2-inch flange diameter make the intended axle and hub dimensions explicit. The flange helps locate the bearing in a compatible wheel, while 2RS rubber seals are stated to retain grease and keep dirt, dust, water, and grass clippings out. GCr15 chrome steel is specified for durability and load capacity. Four pieces support replacement across compatible wheels, and the listed cross-references include several mower bearing codes.

Skip it if you have 5/8-inch axles; GICOOL’s sealed flanged bearings are specified for that smaller bore.

This set suits owners replacing 3/4-inch-axle mower-wheel bearings who value double rubber seals and stated chrome-steel construction. Check the 1-3/8-inch hub and flange dimensions against the wheel before installation.

Listed on Amazon as: DEEG 4 PCS 3/4" Flanged Bearings Premium Bearing Steel ID 3/4" x OD 1-3/8"

#2 · Best Conversion Kit

2. KINTLE Conversion Kit

• Material: Alloy Steel
• Material Type: Alloy Steel
• Compatible Lubricant: Grease

Best for: Bushing-to-bearing conversion kits.

Why it ranks #2: The 3/4-inch ID and 1-3/8-inch OD bearings come with thrust washers, retaining rings, hub caps, and washers for a bushing conversion.

This KINTLE kit combines four sealed flanged hub bearings with thrust washers, retaining rings, and hub caps, enabling a more complete front-wheel bushing-to-bearing conversion. Its 3/4-inch inner diameter and 1-3/8-inch outer diameter target the specified shaft and rim dimensions.

The kit supplies four bearings, four heat-treated thrust washers, two retaining washers, two E-type retaining rings, and two hub caps, reducing the need to source listed conversion hardware separately. The 3/4-inch inner diameter and 1-3/8-inch outer diameter define the wheel fit. KINTLE identifies compatibility with several Craftsman, Poulan, Husqvarna, Jonsered, and Murray mower references. The thrust washers are specifically recommended for converting from bushings to bearings, making this set relevant to that repair workflow rather than a bearing-only swap.

Skip it if you need bearings alone rather than conversion hardware; DEEG’s four-piece 3/4-inch bearing set supplies bearings without listed kit components.

Pick this kit when converting compatible front mower wheels from bushings to bearings and needing the included washers, rings, and caps. Its 3/4-inch shaft and 1-3/8-inch rim dimensions define the fit boundary.

Listed on Amazon as: 9040H Front Wheel Bushing to Bearing Conversion Kit Compatible with Craftsman, Poulan, Husqvarna, Jonsered, Murray Lawn Mower Fits 532009040, 532124959, 91334, 491334MA, 5920H, 9040HR, 9040N

#3 · Largest Bearing Pack

3. Bonbo 3/4-Inch Bearings

• Material: Alloy Steel
• Material Type: Alloy Steel
• Compatible Lubricant: Grease

Best for: Bulk three-quarter-inch replacements.

Why it ranks #3: This ten-piece set matches a 3/4-inch shaft and 1-3/8-inch hub, with double seals and stated 1,500-pound dynamic load capacity.

Bonbo supplies ten flanged bearings with a 3/4-inch bore and 1-3/8-inch outside diameter, giving multi-wheel repairs a substantial quantity in a defined size. Double seals on both sides help retain lubricant and keep impurities from entering the bearing.

The 3/4-inch bore and 1-3/8-inch outside diameter identify the shaft and hub fit, while the 1-1/2-inch flange diameter and 5/64-inch flange thickness add useful installation dimensions. Bonbo lists a 1/2-inch inside-ring height and 7/16-inch outer-ring height for further comparison with the existing bearing. Double seals help protect lubricant from contaminants. A ten-piece supply suits repeated replacements, and the listed dynamic limits are 1,500 pounds and 4,600 rpm.

Skip it if you need a 1/2-inch shaft bearing; Bonbo’s ten-piece 1/2-inch-bore set matches that smaller axle size.

Choose this bulk set for compatible 3/4-inch shafts and 1-3/8-inch hubs when several mower or cart wheels need bearings. Its seal and detailed dimensions aid selection, but smaller axle sizes require another bearing.

Listed on Amazon as: Bonbo 10Pcs Flanged Ball Bearings ID 3/4" x OD 1-3/8" for Lawn Mower, Wheelbarrows, Carts, Hand Trucks Wheel Alternative to 532009040, AM118315, AM127304, 10513, 251210 Etc, Deep Groove Ball Bearing

#4

4. XiKe 3/4-Inch Bearings

• Material: Alloy Steel
• Material Type: Alloy Steel
• Compatible Lubricant: Grease

Best for: Three-quarter-inch axle replacements.

Why it ranks #4: Four alloy-steel bearings fit a 3/4-inch shaft and 1-3/8-inch hub, and the listing provides several mower replacement codes for reference.

A 3/4-inch bore paired with a 1-3/8-inch outside diameter gives this four-pack a clear fit target for compatible mower wheels. XiKe specifies chrome steel and a seal that retains grease and blocks impurities, supporting a protected replacement for lawn mowers and other listed wheeled equipment.

Match the bearing’s 3/4-inch bore to the shaft and its 1-3/8-inch outside diameter to the wheel hub; those dimensions are the key installation checks. The flanged style suits the listed wheel use, while the seal helps keep grease in and impurities out, reducing exposure during outdoor work. Chrome steel provides the stated durable construction. The four-piece pack can supply multiple compatible wheels, and the listed applications also include wheelbarrows, garden carts, hand trucks, pressure washers, and generators.

Skip it if you need a 5/8-inch bore; AR-PRO’s 5/8-inch carbon-steel bearings match that axle size.

Choose this pack for a mower or other listed equipment with a 3/4-inch shaft and 1-3/8-inch hub. Its sealed, chrome-steel construction suits an outdoor replacement, but the dimensions—not reference codes—should guide fit.

Listed on Amazon as: XiKe 4 Pack Flanged Ball Bearing ID 3/4" x OD 1-3/8" Lawn Mower Bearings

#5 · Eight-Piece Set

5. WAYMASTER 3/4-Inch Bearings

• Material: Alloy Steel
• Material Type: Alloy Steel
• Compatible Lubricant: Grease

Best for: Eight-piece sealed bearing supply.

Why it ranks #5: The eight-piece set fits a 3/4-inch bore and 1-3/8-inch OD; its listing also specifies double inner-raced construction and sealed bearings.

WAYMASTER packages eight hardened-steel bearings with a 3/4-inch bore and 1-3/8-inch outside diameter, combining a larger quantity with dimensions listed for many standard hubs. Its completely sealed, double-inner-raced construction is specified for dusty and debris-exposed use without added greasing.

The 3/4-inch bore and 1-3/8-inch outside diameter define the shaft and hub fit, while the listed 1-1/2-inch flange diameter and 5/64-inch flange thickness offer additional sizing details. Hardened steel and a completely sealed, double-inner-raced design are stated features for everyday use in dusty or debris-filled environments. The product says no greasing is needed, simplifying maintenance after installation. Eight bearings provide spares or supply for multiple compatible mower, wheelbarrow, cart, or hand-truck wheels.

Skip it if you need a 5/8-inch bore; AR-PRO’s four-pack uses that axle size and lists carbon-steel construction.

This pack fits buyers maintaining several compatible wheels with 3/4-inch shafts and 1-3/8-inch hubs. Its sealed design and stated no-grease requirement suit debris-exposed use; confirm the wheel’s dimensions before choosing.

Listed on Amazon as: 8 Pack Flanged Ball Bearings ID 3/4 x OD 1-3/8 Inch, Applicable Lawn Mower, Wheelbarrows, Carts & Hand Trucks Wheel, Replacement 532009040, AM118315, AM127304, 10513, 251210 Etc

#6 · Best 5/8-Inch Fit

6. GICOOL 5/8-Inch Bearings

• Material: Alloy Steel
• Material Type: Alloy Steel
• Compatible Lubricant: Grease

Best for: Sealed five-eighths-inch replacements.

Why it ranks #6: Four sealed flanged bearings specify a 5/8-inch ID and 35 mm OD, serving mower owners whose axle and hub match those dimensions.

GICOOL specifies bearing-grade steel, seals on both sides, and a flanged edge in this four-pack of 5/8-inch-bore bearings. Together, those features suit matching mower or garden-wagon hubs while the flange helps keep each bearing from sliding into the hub.

The 5/8-inch inner diameter and 35 mm, or 1-3/8-inch, outside diameter identify the axle and hub sizes to match. A 37 mm flange outside diameter and flanged design provide a locating edge that helps prevent the bearing from sliding into the hub. GICOOL describes deep grooves and smooth raceways for quiet rotation, while seals on both sides block contaminants. Bearing steel is specified for hardness and wear resistance, and the four-piece pack suits compatible mowers, wheelbarrows, and garden wagons.

Skip it if you need a 3/4-inch bore; DEEG’s four-piece bearing set is sized for 3/4-inch wheel axles.

This set fits buyers replacing bearings on compatible 5/8-inch axles and 1-3/8-inch hubs. The flange, double-sided seals, and stated bearing-steel construction suit outdoor wheel use, but the specified dimensions remain essential.

Listed on Amazon as: 5/8" Sealed Flanged Steel Bearing, 16mm ID x 35mm OD x 13mm W,4 PK

#7

7. AR-PRO 5/8-Inch Bearings

• Material: Carbon Steel
• Material Type: Carbon Steel
• Compatible Lubricant: Grease

Best for: Five-eighths-inch axle replacements.

Why it ranks #7: The four carbon-steel bearings specify a 5/8-inch ID and 1-3/8-inch OD, with listed use in lawn mowers and other wheeled equipment.

A 5/8-inch bore and 1-3/8-inch outside diameter define this AR-PRO four-pack for matching wheel hubs. Carbon-steel construction and the stated straightforward replacement installation make it a practical option for compatible lawn mowers, wheelbarrows, carts, and hand trucks.

Check the axle and hub before installation: these bearings have a 5/8-inch inner diameter and a 1-3/8-inch outer diameter. That specific sizing narrows the fit to matching wheels rather than 3/4-inch-axle setups. AR-PRO lists carbon steel for wear resistance, while grease compatibility suits the stated lubricant type. The four-piece set is intended as a wheel-bearing replacement, and its listed applications span mowers and several hand-pushed carts, so one size can serve compatible equipment in a garden or workshop.

Skip it if you have a 3/4-inch axle; XiKe’s 3/4-inch-bore flanged bearing is sized for that shaft.

This is a sensible replacement set for owners whose mower or cart uses a 5/8-inch shaft and 1-3/8-inch hub. Its listed carbon-steel build and broad equipment applications are useful, but axle size remains decisive.

Listed on Amazon as: (4-Pack) 5/8" Bearings Carbon Steel – ID 5/8" x OD 1-3/8" Applicable Lawn Mower, Wheelbarrows, Carts and Hand Trucks Wheel Bearings Replacement

#8

8. XiKe 1/2-Inch Bearings

• Material: Alloy Steel
• Material Type: Alloy Steel
• Compatible Lubricant: Grease

Best for: Half-inch shaft, larger hubs.

Why it ranks #8: Four alloy-steel bearings fit a 1/2-inch shaft and 1-3/8-inch hub, with grease-retaining seals and listed mower replacement references.

XiKe pairs a 1/2-inch bore with a 1-3/8-inch outside diameter, a useful combination for compatible wheels whose shaft and hub sizes differ from smaller-hub bearings. The four flanged alloy-steel bearings have seals that retain grease and help keep impurities out.

Use the 1/2-inch bore to match the shaft and the 1-3/8-inch outside diameter to match the hub; this combination is the defining fit point. The flange suits wheel installation, while the stated seal helps retain grease and exclude impurities during outdoor use. XiKe lists smooth, low-noise operation and alloy-steel material. Four pieces provide replacements for more than one compatible wheel, and the listed applications extend to wheelbarrows, garden carts, hand trucks, pressure washers, and generators.

Skip it if you have 1-1/8-inch hubs; Sunluway’s 1/2-inch-bore bearing uses that smaller outside diameter.

This set suits a mower or other listed machine with a 1/2-inch shaft and a 1-3/8-inch hub. The seal and flanged form support wheel replacement, while checking both dimensions prevents choosing the wrong hub size.

Listed on Amazon as: XiKe 4 Pack Flanged Ball Bearings 1/2" x 1-3/8" x 1/2" inch

#9

9. Bonbo 1/2-Inch Bearings

• Material: Alloy Steel
• Material Type: Alloy Steel
• Compatible Lubricant: Grease

Best for: Half-inch axle bulk replacements.

Why it ranks #9: This ten-piece flanged set fits a 1/2-inch bore and 1-1/8-inch OD, with a stated 1,600-pound dynamic load limit.

Ten flanged bearings with a 1/2-inch bore and 1-1/8-inch outside diameter give this Bonbo set a compact, clearly specified fit for matching wheel hubs. Its listed deep-groove design and alloy-steel construction suit replacements across mowers, wheelbarrows, carts, and hand trucks.

The 1/2-inch bore and 1-1/8-inch outside diameter identify the shaft and hub dimensions to match before fitting. Bonbo also lists a 1/2-inch inside-ring height, 25/64-inch outer-ring height, and 5/64-inch flange thickness, which help distinguish this bearing from other nominally similar sizes. The ten-piece quantity is useful when several compatible wheels need service. Its stated 1,600-pound limit dynamic load and 4,600-rpm limit dynamic speed provide operating specifications for buyers comparing replacements.

Skip it if you need a 1-3/8-inch hub bearing; XiKe’s 1/2-inch-bore, 1-3/8-inch bearing has the larger outside diameter.

Choose this bulk set for compatible 1/2-inch shafts and 1-1/8-inch wheel hubs, especially when multiple bearings are needed. The listed ring and flange dimensions help with size checks; its hub diameter is the key boundary.

Listed on Amazon as: Bonbo 10Pcs Flanged Ball Bearings 1/2" x 1-1/8" x 1/2" for Lawn Mower, Wheelbarrows, Carts & Hand Trucks Wheel Hub, Double Seal Deep Groove Ball Bearings

#10

10. Sunluway 1/2-Inch Bearings

• Material: Alloy Steel
• Material Type: Alloy Steel
• Compatible Lubricant: Grease

Best for: Half-inch shafts, compact hubs.

Why it ranks #10: The ten-piece set fits a 1/2-inch shaft and 1-1/8-inch hub and lists double seals, but offers the same core size niche as another option.

Sunluway’s ten-piece set combines a 1/2-inch bore with a 1-1/8-inch outside diameter, targeting mower wheels and carts with compact hubs. Double seals and pre-lubrication are stated features, giving buyers a protected, ready-lubricated option for matching wheel replacements.

Match the 1/2-inch bore to the shaft and the 1-1/8-inch outside diameter to the wheel hub; Sunluway lists use with flat-free wheels up to that hub size. The double-sealed design and pre-lubrication help protect the bearing and avoid adding lubricant during initial installation. Chromium steel is specified for a single-row bearing supporting radial loads. Ten pieces provide a substantial supply for compatible mower, cart, or hand-truck wheels, with pressure washers, generators, and air compressors also listed.

Skip it if you need a 1-3/8-inch hub size; Bonbo’s ten-piece 3/4-inch bearing set uses that larger outside diameter.

Choose these for compatible 1/2-inch shafts and 1-1/8-inch hubs when multiple wheels need service. The double seals and pre-lubrication suit outdoor equipment, but the compact hub size is not interchangeable with larger hubs.

Listed on Amazon as: ID 1/2" x OD 1-1/8" Flanged Ball Bearings 10PCs for Lawn Mower, Wheelbarrows, Carts & Hand Trucks Wheel Hub, Alternative to MTD,12118 & Rotary 324 Etc. Double Seal Deep Groove Ball Bearings